Longhair1957
Member
https://m.youtube.com/watch?v=lpxriCVhciA
Here is the new 1895 Ruger/marlin
- Thread starter Longhair1957
- Start date
Welcome to ArizonaShooting.org!
Join today!
Welcome! You have been invited by Black_water to join our community. Please click here to register.
oldslurrydog1
Member
Nice
Suck My Glock
Member
I realize it won't happen right away, because Ruger has a learning curve here to get Marlin properly spun up again.
But once Marlin is rocking again,...PLEASE make a take-down 1894 .357 carbine with a threaded muzzle,...preferably in stainless.
Chiappa made it for a brief second (also marketed by Taylor's & Co.) and now they are rare as an honest politician. I'm sure Marlin/Ruger could do it better, as well as keep it in the catalog for more than a few months.
I love my 2017 production CST,...but it would just be that much cooler if it was a takedown model.
But once Marlin is rocking again,...PLEASE make a take-down 1894 .357 carbine with a threaded muzzle,...preferably in stainless.
Chiappa made it for a brief second (also marketed by Taylor's & Co.) and now they are rare as an honest politician. I'm sure Marlin/Ruger could do it better, as well as keep it in the catalog for more than a few months.
I love my 2017 production CST,...but it would just be that much cooler if it was a takedown model.
samnev
Member
I like the idea of a takedown in 357.
Suck My Glock
Member
I call my CST my "mouse fart" gun, because it is so quiet. The same suppressor on the 9mm CMMG Banshee is OK, but on the Marlin, with low-pressure .38spl. target wad-cutters and such,...its like an air gun. And since I can load ammo for it at just slightly more expensive than .22lr,...I'm just a boy with a toy again, like when I was 12.
I get that not all experiences are the same - but I have exactly one bad thing to say about my Remlin (Marlin) 1895GS in 45-70gvt - and that is that the loop is too small for my fat hand and and has a sharpish edge - so my middle-finger knuckle bleeds if I shoot too many rounds in a sitting. Other than that - after 1000 rounds of various stuff including some fairly hot stuff - I love the gun. Guessing that Ruger will make it "better" but I sure do like the one that I have.
BigNate said:
Well, you can replace that loop and get something that doesn't hurt as bad. If the action on yours ever was rough as it came from Remington, I'm guessing you broke it in nice and smooth over your 1000 rounds.
AchillesKobus
New member
If they do this would be great!Suck My Glock said:
AZ_Five56 said:
I've thought about getting a new lever for it but I hear that the interface between the lever and the bolt is a big piece of what determines how smoothly the gun cycles - and that it needs to be "tuned" (no clue if this is true)... I keep telling myself that if I can figure out what stainless alloy it's made out of, pull it out of the gun, open it up, add some material a d TIG it back together. Yeah... that's the ticket... surely easier than just replacing the lever and having a gunsmith fit it properly...
The other thought is to just pull it out and get after the inside edges of the loop with a little sanding cone set to take the hard edge off of it. That would probably make it "good enough" even for my big hands.
Or... I can just bitch and moan about it for another 10 years.
I have had a Remlin SBL for a few years now and have been extremely happy with it. I am sure the Rugers are good also but I am glad to have been enjoying mine rather than waiting for a chance to get one.
After having a lot of fun with the SBL I picked up a 336 BL which has been great also.
After having a lot of fun with the SBL I picked up a 336 BL which has been great also.
brandyspaw
Member
Zpglass said:
And addicting as well. It seems its hard to stop at just one or 2 lever guns.
BigNate said:AZ_Five56 said:
I've thought about getting a new lever for it but I hear that the interface between the lever and the bolt is a big piece of what determines how smoothly the gun cycles - and that it needs to be "tuned" (no clue if this is true)... I keep telling myself that if I can figure out what stainless alloy it's made out of, pull it out of the gun, open it up, add some material a d TIG it back together. Yeah... that's the ticket... surely easier than just replacing the lever and having a gunsmith fit it properly...
The other thought is to just pull it out and get after the inside edges of the loop with a little sanding cone set to take the hard edge off of it. That would probably make it "good enough" even for my big hands.
Or... I can just b**** and moan about it for another 10 years.
My Rem-Marlin 336 has a fairly sharp edge on the lever as well. I just wrapped it in paracord and called it a day. I'm more annoyed that the screw that holds the lever on to the gun walks out over time.
mallic said:BigNate said:AZ_Five56 said:
I've thought about getting a new lever for it but I hear that the interface between the lever and the bolt is a big piece of what determines how smoothly the gun cycles - and that it needs to be "tuned" (no clue if this is true)... I keep telling myself that if I can figure out what stainless alloy it's made out of, pull it out of the gun, open it up, add some material a d TIG it back together. Yeah... that's the ticket... surely easier than just replacing the lever and having a gunsmith fit it properly...
The other thought is to just pull it out and get after the inside edges of the loop with a little sanding cone set to take the hard edge off of it. That would probably make it "good enough" even for my big hands.
Or... I can just b**** and moan about it for another 10 years.
My Rem-Marlin 336 has a fairly sharp edge on the lever as well. I just wrapped it in paracord and called it a day. I'm more annoyed that the screw that holds the lever on to the gun walks out over time.
I thought about doing that (or with leather) but it is already really pretty tight on my hand. I guess I could wrap it with cheap paracord and if it still fits the hand I can do it right...
If the Big Loop replacement levers weren't made of unobtanium, or $200 when you can find them, I would have them on both my 336.
I am a Lever gun fanatic, i have many Marlins, Winchesters, Rossi's, a Chiappa 1886, Henrys and even a couple custom 1895s from Wild West Guns and Brockmans Custom (now defunct). I have 3 Remlins 2 1894s and an 1895 SBL they have all been fine for me. I like that i don't care as much about them so they are truly tools but functional tools.
I frankly have more issues with my older original Marlins than the remlins. I do not own a new Ruger/Marlin as the prices are just too whacked for me and there not that much better. I want to get one to see but i will wait a while to see what the market and what models they make.
I have replaced many levers on my Marlins with big loops from Wild West Guns and Beartooth Mercantile. While the lever interface is important to the function of a Marlin 1894,95 or 336 i have found that the replacement levers have in general have proper angles cut and work without tuning just fine.
Tuning is really not difficult and there are lots of tutorials online. If one can cut and tig weld a lever they could certainly tune a replacement lever should it be needed.
The WWG levers are bigger and would certainly open up that space for most large hands. There are of course other vendors making them. The guy that owns Beartooth Mercantile in Cody Wyoming is very nice and also knowledgeable on the Marlin Lever guns. He could certainly talk to you about issues with installation and tuning.
I frankly have more issues with my older original Marlins than the remlins. I do not own a new Ruger/Marlin as the prices are just too whacked for me and there not that much better. I want to get one to see but i will wait a while to see what the market and what models they make.
I have replaced many levers on my Marlins with big loops from Wild West Guns and Beartooth Mercantile. While the lever interface is important to the function of a Marlin 1894,95 or 336 i have found that the replacement levers have in general have proper angles cut and work without tuning just fine.
Tuning is really not difficult and there are lots of tutorials online. If one can cut and tig weld a lever they could certainly tune a replacement lever should it be needed.
The WWG levers are bigger and would certainly open up that space for most large hands. There are of course other vendors making them. The guy that owns Beartooth Mercantile in Cody Wyoming is very nice and also knowledgeable on the Marlin Lever guns. He could certainly talk to you about issues with installation and tuning.
