Glock bulge

[Ranger1]

Who here reloads brass fired from a glock??

[Jack Dupp]

This guy.

[Ranger1]

Nice.....

[338lapua]

To deal with the bulge you can get one of these, cheapest commercial machine I know of. They are made in Arizona

http://www.magmaengineering.com/case-ma ... ase-sizer/

Or if you only shoot a few thousand a year you can use one of these.

http://www.magmaengineering.com/case-ma ... ase-sizer/

If money is no object get one of these.

http://www.camdexloader.com/Zoom.htm?Ap ... rLarge.jpg

[17-21-23]

I have SS lee press and push the entire case thru the sizing die. Think I paid $50 for the whole set up, if that.

[Flash]

I reload 9MM and .45 ACP and .380 ACP that have been fired from a glock on an almost weekly basis.

I don't do anything special at all to them, just run them through a Lee sizing/decapping die like I do with all other cases and load 'em up.

Never had a problem and I pick up range brass like you wouldn't believe. I even have the R.O.'s shoving other peoples empties down to me.

[Harrier]

I run all my 40 range pickups thru a Lee bulge Buster die. My XD has a supported chamber so I only have to do it once.

[792mauser]

Done it plenty of times. Just pass it through the sizer and off to the races. I even shoot predominantly lead through it.just pass a brush a few times per few hundred rounds.

[Intel6]

Do it all the time, 9mm/40/10mm/45 ACP.

[mikeAZ]

Me too....I shoot all range brass and load LOT'S of 9mm. Lee "U" die about $25.00. There are other inexpensive options to resize 9mm .. See video of the Bulge Buster setup that uses the Lee 9x18 seating die

[mikeAZ]

Me too....I shoot all range brass and load LOT'S of 9mm. Lee "U" die about $25.00. There are other inexpensive options to resize 9mm .. See video of the Bulge Buster setup that uses the Lee 9x18 seating die. Lee 9x18 Mackrov .. EBay, about $20.00

[lew]

Neither my G19 or my wife's G26- both Gen. 4's- bulge the brass, and I don't pick up other people's discarded brass.

[NBC_LT]

To deal with the bulge you can get one of these, cheapest commercial machine I know of. They are made in Arizona

http://www.magmaengineering.com/case-ma ... ase-sizer/

Or if you only shoot a few thousand a year you can use one of these.

http://www.magmaengineering.com/case-ma ... ase-sizer/

If money is no object get one of these.

http://www.camdexloader.com/Zoom.htm?Ap ... rLarge.jpg

Ive been using Magma Engineering's Casemaster Jr. for years in order to reload 9mm shot from an open-bolt SMG. Brass shot from an open bolt will fail resizing/case gage about 1/15. The Casemaster Jr. allows me to reload ballooned brass up to 3 times - they start failing after 5 loads. Going to get the kit to reload my .308 out of the 1919 - headspacing creates a ballooning effect with this brass as well.

[storage_man]

To deal with the bulge you can get one of these, cheapest commercial machine I know of. They are made in Arizona

http://www.magmaengineering.com/case-ma ... ase-sizer/

Or if you only shoot a few thousand a year you can use one of these.

http://www.magmaengineering.com/case-ma ... ase-sizer/

If money is no object get one of these.

http://www.camdexloader.com/Zoom.htm?Ap ... rLarge.jpg

Ive been using Magma Engineering's Casemaster Jr. for years in order to reload 9mm shot from an open-bolt SMG. Brass shot from an open bolt will fail resizing/case gage about 1/15. The Casemaster Jr. allows me to reload ballooned brass up to 3 times - they start failing after 5 loads. Going to get the kit to reload my .308 out of the 1919 - headspacing creates a ballooning effect with this brass as well.

A small base .308 sizing die works miracles on 1919 shot brass.

[omegaman]

I've reloaded many rounds of it some myth that it is no good? If you want to see case bulge try a open bolt with fast powder like tight group.