Wet Tumbler... Juice Worth the Squeeze?

[BigNate]

For what it's worth, I have had good luck using a small amount of citric acid and the combo car wash/wax like the Turtle or Jay Leno's Garage brands.

If the brass is already clean, and you're just looking for shine, you can forego the soap altogether and just use a bit of citric acid. That only takes about an hour, possibly less. However, unless it's heavily tarnished, I've decided that the rinsing and drying just isn't worth it. I've gone back to corncob and Nu-Finish for light polishing.

I'm a "function over form" guy... I mostly don't care how shiny they are... but I do want them to be clean, primer pockets clean, etc... for consistency in reloading...

[BigNate]

Thanks for all the advice to avoid the pins... sounds like that is generally the consensus...

I'm thinking that for now I'll try the idea of insulating the vibratory cleaner from the ground and then doing the box with a blanket over it... I may actually get ambitious and line the box with the Styrofoam insulation too... maybe that will be enough that it does not keep me awake...

[Old Jeff H]

Well the pins will get your primer pockets clean. That's the one thing that they really are good for. And getting the inside of straight-walled brass clean.

However, if you're uniforming your primer pockets like I do on all my rifle brass, getting the pockets clean beforehand is redundant.

I guess what I'm trying to say is, if I want really really clean pistol brass, I'll use the wet tumbler with pins.

[condition_0ne]

I have a Frankfort rortary wet tumbler with pins for sale if you're interested. That said, wet tumbling w/ pins vs vibratory with corn/walnut media gives very different results and might be good or bad depending on what you're trying to accomplish. For my process with rifle cases I went back to walnut/corn media vs. the pins/wet tumbling as I get more consistent case neck tension with the corn media. The pins actually get the case necks *too* clean and the case neck grip is slightly less consistent. For pistol cases, particularly .357/.44 mag rounds the steel media works great.

[condition_0ne]

when i first used the cement mixer, i destroyed a couple buckets of 223 brass, thinking i had it dry enough, and stashed it, months later it was that ugly black, tarnish, and nope wouldn't come clean, learned my lesson, have the FA tube tumblers, and run's long and fast, have the cleaner and pins, tried it a few times and decided the dry stuff works fine, without themess and hassle of the wet. might try sometime in future again, but not on the list presently, good luck with selection. also have the tub type vibrators the dillons are reasonabl y quiet, and have to admit some of those sobs are louder than my old hot rod.
rj

Got your PM, can't send PMs yet due to new account (lol?). Please text me, 442.271.5798 for the tumbler etc. The tumbler I have: https://www.frankfordarsenal.com/case-c ... 09544.html plus a full helping of steel pins.

[condition_0ne]

How many posts before my PMs are unlocked? I had an account here ages ago but it was deleted. I made a new one and now I don't have any privileges.

[leadman1]

I have the wet and corn cob tumblers. I like both but when I use the wet I will let them dry then run them in the corncob with new finish for a bit. Keeps them from tarnishing so fast versus wet with no corn cob.
I found if you keep the water level low in the FA it helps keep the caps from leaking and still cleans well.

[Bottom Gun]

I considered wet tumbling but, with the rinsing and drying, it sounds like more work than using corn cob or walnut.

However, my main reason for dry tumbling is because I prefer to process my brass after it’s clean. I shoot in the desert so my recovered brass is almost always dusty and/or covered with grit. I really don’t want to run that grit through my sizing dies. So I’ll stick with walnut and corn cob.

A sheet of vibration dampening foam under your tumbler will reduce the noise quite a bit.

[Old Jeff H]

I have the wet and corn cob tumblers. I like both but when I use the wet I will let them dry then run them in the corncob with new finish for a bit. Keeps them from tarnishing so fast versus wet with no corn cob.

I started doing the same thing a couple of months ago. It's a bit of work, but gives you the best results possible.

[M60Tanker]

I've got one of those Frankford wet tumblers available for $150. I've found dawn and Lemi-shine work great, those pins get everywhere! I agree about the little harbor freight mortar mixer, a little dawn/shine and let 'em roll around. I re-use the solvent, pour it in a bucket for next time. Rinse with hose water 2X and dump that. I dry the brass on an old rag towel or 3, sitting in the AZ sunshine.

[Lucafu1]

I use the Frankford w/o pins and use RCBS ultra sonic solutions. Works great. I did use pins but it isn't worth the hassle. They get super clean and you can't even tell they have been annealed either. I'm about to run some huge batches soon actually. Rinse well in hot water and put them in my dryer (no longer use the oven). No problems ever.

[Lucafu1]

Duplicate

[knockonit]

have a couple sonic units, and use them occassionally, but after destroying some brass by not getting 100% dry then packing away, i picked up a free electric stove and put it on patio with a cord, and now dry'm fast and easy, stove is used for other items also, so no war with teh dragon lady

[azshooter887]

never go back once you start wet tubling

[M60Tanker]

I've tumbled brass for a long time. These days I wet tumble using a cheap/smaller Harbor Freight mortar mixer with dawn and lemi-shine, and NO pins. Sort for size first, let it run, pour out the liquid, put some water in, let it run. Rinse/repeat. Spread the brass out on a towel and let the sun dry it out. I only use corn cob tumbling for removing the Dillon Case lube when ammo is loaded.